Operating the Camera from a PC

12. Remote Operations
Tethered Recording
Operating the Camera from a PC

Connect the camera and PC with a USB connection cable, LAN cable or Wi-Fi.

When connecting the camera directly to a PC with a USB connection cable or LAN cable, you can connect to “LUMIX Tether” with the default setting. Proceed to step 2. (Operate from step 1 if you change the default setting of [LAN / Wi-Fi] or [USB Mode] in the [Setup] ([IN/OUT]) menu.)

When connecting with Wi-Fi, output the camera menu screen via HDMI/SDI to an external monitor etc. (Connecting the external monitor)

img_ch12_03

maru_alphabet_a [LAN] terminal

maru_alphabet_b [USB] terminal

maru_alphabet_c LAN cable (commercially available) or maru_alphabet_d USB connection cable (commercially available)

maru_alphabet_e PC (commercially available)

Plug in/out straight holding onto the plug. (Inserting these at an angle may cause deformation or malfunction)

Do not connect the cable to the wrong terminals. This may cause a malfunction.

Preparation:

Turn on the camera and PC.

Install “LUMIX Tether” on PC.

1(When connecting with a USB connection cable)
Set [USB Mode] to [PC(Tether)].

[MENU/SET] arrow_menu [ menuicon_setup ] [ menuicon_in_out ] [USB Mode] [PC(Tether)]

(When connecting with a LAN cable)
Set the camera to DHCP server before setting it to a wired LAN connection setting.

[MENU/SET] arrow_menu [ menuicon_setup ] [ menuicon_in_out ] [LAN / Wi-Fi] [LAN / Wi-Fi Setup] [IP Address Setting (LAN)] [DHCP Server]

If you changed the setting of [IP Address Setting (LAN)], turn the camera off and then on again.

[MENU/SET] arrow_menu [ menuicon_setup ] [ menuicon_in_out ] [LAN / Wi-Fi] [LAN / Wi-Fi Function] [New Connection] [Control With LUMIX Tether] [LAN]

(When connecting with Wi-Fi)
Set the camera to a Wi-Fi connection setting.

[MENU/SET] arrow_menu [ menuicon_setup ] [ menuicon_in_out ] [LAN / Wi-Fi] [LAN / Wi-Fi Function] [New Connection] [Control With LUMIX Tether] [Wi-Fi] [Via Network] / [Direct]

For details about [Via Network] and [Direct]. (Wi-Fi Connections)

Proceed to Step 3.

sc_cap_wifi_connect

2Connect the camera and PC with the USB connection cable or LAN cable.

At default setting, the camera is set to DHCP server. By connecting the camera directly to your PC with a LAN cable, you can connect the camera to your PC without manually setting network information such as the IP address.

When using PoE+ power supply with the camera, connect a PoE+ compatible switching hub and PC with a LAN cable.

3Use “LUMIX Tether” to operate the camera from the PC.

(When connecting for the first time with a LAN cable or Wi-Fi)

Set a password to connect to the camera from “LUMIX Tether”. (from 8 to 31 characters)

A tether icon is displayed in the upper right of the screen during recording standby.

Terminating the Network Connection

To terminate the network connection between the camera and PC, follow the steps below.

number_k_01 On the PC, close the “LUMIX Tether”.

number_k_02 Terminate the network connection.

[MENU/SET] arrow_menu [ menuicon_setup ] [ menuicon_in_out ] [LAN / Wi-Fi] [LAN / Wi-Fi Function] [Yes]

You can also perform the same operation by pressing the Fn button assigned with [LAN / Wi-Fi]. (Fn Button Assigned with [LAN / Wi-Fi])

sc_cap_wifi_close

For the USB connection cable, use one that is a shielded product with a ferrite core compliant to USB Type C (USB3.1) that is less than 1.5 m (4.9 feet).

For the cable that connects to the LAN terminal, use the one below.

–LAN cable (STP (Shielded Twisted Pair), category 5e or above, maximum 100 m (328 feet))

If the camera is connected to PC using both of LAN cable and USB connection cable, the USB connection cable will be prioritized.

Wi-Fi/Bluetooth function cannot be used while the connection is being made using a USB connection cable or LAN cable.

When you use [Reset] in the [Setup] ([Setting]) menu to reset the network settings, the password to connect to the camera from “LUMIX Tether” will also be reset.

The camera cannot be connected to “LUMIX Tether” and “LUMIX Sync” at the same time.

Operating multiple cameras

You can operate multiple cameras remotely using “LUMIX Tether”.

The connecting method differs depends on whether you set the camera to a setting for DHCP server or DHCP client to connect.

img_ch12_04

maru_alphabet_a LAN cable (commercially available)

maru_alphabet_b Router (commercially available)

maru_alphabet_c PC (commercially available)

Example: When the DHCP server is within the LAN and the camera is set to DHCP client to connect.

1Set the camera to a DHCP client.

[MENU/SET] arrow_menu [ menuicon_setup ] [ menuicon_in_out ] [LAN / Wi-Fi] [LAN / Wi-Fi Setup] [IP Address Setting (LAN)] [DHCP Client]

If you changed the setting of [IP Address Setting (LAN)], turn the camera off and then on again.

2Connect all cameras and the router with LAN cables.

3Connect the router and PC with a LAN cable.

4Operate “LUMIX Tether” to operate the camera remotely.

Tether Connection Mode

You can set the camera to tether connection mode by operating the camera remotely from “LUMIX Tether”.

If you set the camera to tether connection mode when it is not recording, it enters a connection standby state for LUMIX Tether while maintaining the connection between the camera and PC, and it can quickly return to a state where remote shooting is possible.

The status indicator lights up (orange) during tether connection mode.

For how to operate the software, refer to the operation guide for “LUMIX Tether”.

Taking a still picture

You can take still pictures by operating the camera remotely from the operation panel of “LUMIX Tether”.

When you are recording still pictures you can use the functions which are not available during video recording.

The functions for still pictures are not displayed on the menu screen.

The setting items differ from those during video recording.

Example)

Recording mode	[P] / [A] / [S] / [M]
Shutter speed (sec.)	1 to 1/16000
Exposure Compensation	[±5EV] When the exposure compensation value falls below or exceeds ±3 EV, the brightness of the recording screen will no longer change.
Picture quality	JPEG (FINE / STD.)
Picture size	[L] / [M] / [S]
Image Stabilizer	[Panning]
1 shot AF	Available

The following settings are fixed:

–[Aspect Ratio]: [4:3]

–[Photo Style]: [Standard]

[P] / [A] / [S] / [M] mode can be used only during Tether recording.

After finishing Tether recording, select [Creative Video Mode] in [Rec Mode].

For how to operate the software, refer to the operation guide for “LUMIX Tether”.