Panasonic

Format that can be output from the SDI OUT terminal [X2]

The format that can be output from the <SDI OUT> terminal differs with following combination of the settings.

bullet02[SYSTEM] menu character_arrow [FREQUENCY]

bullet02[SYSTEM] menu character_arrow [REC FORMAT]

bullet02[VIDEO OUT/LCD/VF] menu character_arrow [VIDEO OUT SEL] character_arrow [SDI OUT FORMAT]


Set to the following settings in the menus when outputting only to the <SDI OUT> terminal.

bullet02[VIDEO OUT/LCD/VF] menu character_arrow [VIDEO OUT SEL] character_arrow [SDI + HDMI OUTPUT] character_arrow [OFF]

bullet02[VIDEO OUT/LCD/VF] menu character_arrow [VIDEO OUT SEL] character_arrow [EXTERNAL OUT SEL] character_arrow [SDI]


It is also possible to output to both the <SDI OUT> terminal and the <HDMI> terminal. (character_referenceNote regarding simultaneous output to the SDI OUT terminal and the HDMI terminal [X2])


character_diamondWhen the [FREQUENCY] is set to [59.94Hz]

[REC FORMAT]

[SDI OUT FORMAT]: Output Format

Resolution

Frame rate

3840×2160

59.94p

[1920×1080p]: 1920×1080/59.94p 4:2:2 10 bit

[1920×1080i]character_asterisk: 1920×1080/59.94i 4:2:2 10 bit

29.97p

[1920×1080p]: 1920×1080/29.97p 4:2:2 10 bit

[1920×1080PsF]character_asterisk: 1920×1080/29.97PsF 4:2:2 10 bit

23.98p

[1920×1080p]: 1920×1080/23.98p 4:2:2 10 bit

[1920×1080PsF]character_asterisk: 1920×1080/23.98PsF 4:2:2 10 bit

1920×1080

59.94p

[1920×1080p]: 1920×1080/59.94p 4:2:2 10 bit

[1920×1080i]character_asterisk: 1920×1080/59.94i 4:2:2 10 bit

59.94i

[1920×1080i]: 1920×1080/59.94i 4:2:2 10 bit

29.97p

[1920×1080p]: 1920×1080/29.97p 4:2:2 10 bit

[1920×1080PsF]character_asterisk: 1920×1080/29.97PsF 4:2:2 10 bit

23.98p

[1920×1080p]: 1920×1080/23.98p 4:2:2 10 bit

[1920×1080PsF]character_asterisk: 1920×1080/23.98PsF 4:2:2 10 bit

1280×720

59.94p

[1280×720p]: 1280×720/59.94p 4:2:2 10 bit


character_diamondWhen the [FREQUENCY] is set to [50.00Hz]


[REC FORMAT]

[SDI OUT FORMAT]: Output Format

Resolution

Frame rate

3840×2160

50.00p

[1920×1080p]: 1920×1080/50.00p 4:2:2 10 bit

[1920×1080i]character_asterisk: 1920×1080/50.00i 4:2:2 10 bit

25.00p

[1920×1080p]: 1920×1080/25.00p 4:2:2 10 bit

[1920×1080PsF]character_asterisk: 1920×1080/25.00PsF 4:2:2 10 bit

1920×1080

50.00p

[1920×1080p]: 1920×1080/50.00p 4:2:2 10 bit

[1920×1080i]character_asterisk: 1920×1080/50.00i 4:2:2 10 bit

50.00i

[1920×1080i]: 1920×1080/50.00i 4:2:2 10 bit

25.00p

[1920×1080p]: 1920×1080/25.00p 4:2:2 10 bit

[1920×1080PsF]character_asterisk: 1920×1080/25.00PsF 4:2:2 10 bit

1280×720

50.00p

[1280×720p]: 1280×720/50.00p 4:2:2 10 bit

  1. Factory setting


bullet02The 3840×2160 output is not supported.

bullet02User bits are not displayed.

bullet02[SDI OUT FORMAT] restores the factory settings when the settings of [FREQUENCY] and [REC FORMAT] change and the current setting values of [SDI OUT FORMAT] cannot be acquired.

bullet02The output format when playing back from the thumbnail screen is as follows.

– It will be the value set in [SDI OUT FORMAT] when the recording resolution of the playback clip is the same as [REC FORMAT].

– It will be factory setting of [SDI OUT FORMAT] when the recording resolution of the playback clip is different from [REC FORMAT].

bullet02There may be a fews seconds of images not displayed on the external device when the clips are changing over, etc.